heater blower motor replacement - DodgeIntrepid.Net Forums - Dodge Intrepid, Concorde, 300m and Eagle Vision chat
 
LinkBack Thread Tools Rate Thread Display Modes
post #1 of 2 (permalink) Old 09-23-2006, 09:02 PM Thread Starter
Intrepid Newbie
 
goldintrepid99's Avatar
 
Join Date: Aug 2003
Location: brampton
Posts: 60
Feedback: 0 / 0%
 
heater blower motor replacement

hello to all....i need to replace my heater blower motor on my 1999 intrepid.....does some have the how to tips ....do i need to remove the dash or just the glove box???? all help will be great ....thanks
goldintrepid99 is offline  
Sponsored Links
Advertisement
 
post #2 of 2 (permalink) Old 09-24-2006, 10:26 AM
Intrepid Pro
 
Torontofirecaptain's Avatar
 
Join Date: Apr 2004
Location: Whitby, Ontario
Posts: 3,934
Feedback: 71 / 100%
                     
From the FSM:
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS,
DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISOLATE
THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYSTEM
CAPACITOR TO DISCHARGE BEFORE PERFORMING
FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRECAUTIONS
COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
(1) Open the hood and disconnect the negative battery
cable remote terminal from the remote battery
post(Refer to 8 - ELECTRICAL/BATTERY SYSTEM/
CABLES - REMOVAL).
(2) Remove the lower right under panel duct.
(3) Remove the blower motor connector from the
blower motor resistor block/power module.
(4) Squeeze the blower motor wiring grommet and
push the grommet through the blower motor housing
cover.
(5) Remove the blower motor housing cover.
(6) Remove the blower motor retaining screws.
(7) Lower the blower motor from housing.
INSTALLATION
(1) Install the blower motor in the HVAC housing
and tighten the mounting screws to 2.2 Nm (20 in.
lbs.).
(2) Install the blower motor housing cover.
(3) Position the blower motor wiring grommet in
the blower motor housing cover.
(4) Connect the blower motor harness connector to
the blower motor resistor block/power module.
(5) Install the lower right under panel duct.
(6) Connect the negative battery cable remote terminal
to the remote battery post(Refer to 8 - ELECTRICAL/
BATTERY SYSTEM/CABLES -
INSTALLATION).
HVAC HOUSING
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIRBAGS,
DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISOLATE
THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYSTEM
CAPACITOR TO DISCHARGE BEFORE PERFORMING
FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRECAUTIONS
COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
WARNING: REVIEW THE WARNINGS IN THE FRONT
OF PLUMBING BEFORE PERFORMING THE FOLLOWING
OPERATION. (Refer to 24 - HEATING & AIR
CONDITIONING/PLUMBING - WARNING)
(1) Open the hood and disconnect the negative battery
cable remote terminal from the remote battery
post(Refer to 8 - ELECTRICAL/BATTERY SYSTEM/
CABLES - REMOVAL).
(2) Remove the instrument panel from vehicle(Refer
to 23 - BODY/INSTRUMENT PANEL/INSTRUMENT
PANEL ASSEMBLY - REMOVAL).
(3) Recover the refrigerant from the system. (Refer
to 24 - HEATING & AIR CONDITIONING/PLUMBING
- STANDARD PROCEDURE - REFRIGERANT
RECOVERY)
(4) Drain the engine cooling system(Refer to 7 -
COOLING - STANDARD PROCEDURE).
(5) Remove the air cleaner hose and air distribution
duct from the engine.
(6) Remove the spring type heater hose fasteners
at the dash panel and remove the hoses from heater
core. Plug the heater core inlet and outlet tubes to
prevent anti-freeze from spilling on the vehicle interior
during removal. If an appropriate plug cannot be
found pull back carpet and use caution when removing
the HVAC housing. Keep the heater tubes elevated
to prevent spillage of coolant.
(7) Remove one nut at expansion valve retaining
both A/C lines to expansion valve. After removing the
lines cap the expansion valve openings and the A/C
hose openings. This will prevent any dirt or moisture
from entering the refrigerant system during servicing.
CAUTION: The lubricant used in this air conditioning
system absorbs moisture readily (similar to
brake fluid). Do not leave any portion of the system
open for extended periods of time.
(8) Remove the three retaining nuts from the
studs. These studs project through the dash panel
into the engine compartment.
(9) Remove two screws to the defrost duct and
remove.
(10) Remove two nuts, and two screws attaching
the HVAC housing to the dash panel.
24 - 24 DISTRIBUTION LH
BLOWER MOTOR (Continued)


goal - have one of my parts on every DI car:biggrinfl
Honoured to be January 2007 COTM.THANK YOU ALL.
Torontofirecaptain is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the DodgeIntrepid.Net Forums - Dodge Intrepid, Concorde, 300m and Eagle Vision chat forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

Member names may only be composed of alpha-numeric characters. (A-Z and 0-9)

!!ATTENTION ADVERTISERS!! If you intend on advertising anything on this forum, whatsoever, you are required to first contact us here . Additionaly, we do NOT allow BUSINESS NAMES unless you are an Authorized Vendor. If you own a business, and want to do sales on this site via posting or private message, you will need to follow the rules. Shops, Stores, Distributors, Group Buys without being authorized will see your account terminated.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Random Question

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes Rate This Thread
Linear Mode Linear Mode
Rate This Thread:



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome