Wipers not working properly and turn signal issues - DodgeIntrepid.Net Forums - Dodge Intrepid, Concorde, 300m and Eagle Vision chat
 
LinkBack Thread Tools Rate Thread Display Modes
post #1 of 4 (permalink) Old 11-08-2018, 11:04 PM Thread Starter
Intrepid Newbie
 
Join Date: Nov 2018
Posts: 1
Feedback: 0 / 0%
 
Wipers not working properly and turn signal issues

Turn signals blink a couple of times then stop and go off, wipers don't turn on with out going up all the way and then back down. Replaced multi function switch wipers now work but turn signal better some times but stops have to switch it on more than once and then it might blink longer say 30 seconds or less. Is there a relay under dash, fuses ok. Chrysler Concorde 2003. Thanks would appreciate any advice. Also have to turn engine on for hazards or turn signals to work, just putting key on without starting does not work.

Last edited by Mark Robertson; 11-08-2018 at 11:16 PM.
Mark Robertson is offline  
Sponsored Links
Advertisement
 
post #2 of 4 (permalink) Old 11-09-2018, 08:18 AM
Intrepid Pro
 
Join Date: Feb 2002
Location: Virginia, U.S.
Posts: 16,307
Feedback: 4 / 83%
                     
(maybe a moderator can move this thread to a 2nd gen. forum)

The hazards should work with ign. on or off. Turn signals work only with key in RUN position.

First - check Fuses O (in PDC in engine compartment) and 9 (in junction block - behind driver’s side dash end cover). Best not to go by visual inspection of fuses - they can fool you - check continuity with meter.

If fuses OK, you may need a new flasher - under dash - remove driver’s side knee bolster. It’s on a panel with some connectors. It’s black - towards bottom left of that panel IIRC. Flasher can be difficult to remove. Most people abandon it in place and pull the connector off and plug in the new flasher and zip tie it to some nearby wires. But if you remove the screw that attaches that connector panel to the underdash structure, you can stick a screwdriver into the latch slot that secures the flasher to that panel to unlatch the flasher and remove it.

Most aftermarket flashers, even though listed for our cars in the applications lists, do not work properly on our cars - some even blow one of the fuses every time you use the hazards. Best to get the OEM flasher from the dealer or from a junk yard.

It’s possible there is a loose connector or bad wire, but my bet is on a blown fuse or flaky flasher.


'98 LXi - Later Concorde gages (black w/ chrome rings)/'99 LX - LHS gages (white) - HIR bulbs

Last edited by peva; 11-09-2018 at 08:30 AM.
peva is offline  
post #3 of 4 (permalink) Old 11-09-2018, 08:24 AM
Intrepid Pro
 
Join Date: Feb 2002
Location: Virginia, U.S.
Posts: 16,307
Feedback: 4 / 83%
                     
Oh - download a factory service manual from here
https://www.dodgeintrepid.net/113-se...ce-manual.html
or here
https://www.dodgeintrepid.net/113-se...df-format.html

Any ‘02 thru ‘04 LH factory manual is good for ‘02 thru ‘04 LH car - no significant changes during that range of years.

Wiring diagrams are in section 8W. Includes diagrams showing PDC and Junction Block fuse numbering (secs. 8W-10 and 12).

Last edited by peva; 11-09-2018 at 11:41 AM.
peva is offline  
Sponsored Links
Advertisement
 
post #4 of 4 (permalink) Old 11-09-2018, 04:07 PM
tgs
Intrepid Pro
 
Join Date: Aug 2006
Location: Stuck in Indianapolis until the end of time
Posts: 1,906
Feedback: 3 / 100%
                     
I believe the black (square and box like) flasher is together with a blue connector, orange connector and green connector and there is one screw that attaches them to the body above and to the left of the brake pedal.

Hope that helps you locate it...
tgs is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the DodgeIntrepid.Net Forums - Dodge Intrepid, Concorde, 300m and Eagle Vision chat forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

Member names may only be composed of alpha-numeric characters. (A-Z and 0-9)

!!ATTENTION ADVERTISERS!! If you intend on advertising anything on this forum, whatsoever, you are required to first contact us here . Additionaly, we do NOT allow BUSINESS NAMES unless you are an Authorized Vendor. If you own a business, and want to do sales on this site via posting or private message, you will need to follow the rules. Shops, Stores, Distributors, Group Buys without being authorized will see your account terminated.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes Rate This Thread
Linear Mode Linear Mode
Rate This Thread:



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome