Diagram for washer motor? - DodgeIntrepid.Net Forums - Dodge Intrepid, Concorde, 300m and Eagle Vision chat
 
LinkBack Thread Tools Rate Thread Display Modes
post #1 of 9 (permalink) Old 09-24-2003, 01:13 PM Thread Starter
Intrepid Pro
 
Candyman's Avatar
 
Join Date: Aug 2001
Location: Columbus, Ohio
Posts: 1,269
Feedback: 3 / 100%
                     
Exclamation Diagram for washer motor?

OK, So the first casualty of my 105k mile vehicle is the windshield washer motor. No more spewing, just leaking. Got under the frame last night to change the oil, the feeding tubes are fine as well as the fuses and electrical connections. Motor no longer pumps....

What I am looking for is a diagram on how to replace this inexpensive part. While lying under the car however, I found there is very limited hand room to navigate this piece.

I'd rather only spend a few bux on the part and fix it myself rather than take it in if possible. Any ideas?
Candyman is offline  
Sponsored Links
Advertisement
 
post #2 of 9 (permalink) Old 09-24-2003, 01:17 PM
Intrepid Modder
 
Hartski's Avatar
 
Join Date: Mar 2003
Posts: 962
Feedback: 0 / 0%
                     
Junkyard
Hartski is offline  
post #3 of 9 (permalink) Old 09-24-2003, 01:22 PM
Intrepid Pro
 
Join Date: Aug 2001
Location: CT
Posts: 11,278
Feedback: 10 / 100%
                     
he asked for info on how to change it, not where to get the part hartski

here's the info right from the service manual


WASHER PUMP MOTOR -INTREPID

REMOVAL
(1) Open hood and disconnect the negative battery
cable remote terminal from the remote battery post.
(2) Remove the left headlamp assembly and set
aside. Refer to Electrical, Lamps/Lighting - Exterior,
Headlamp Unit (Intrepid), Removal.
(3) Remove the four retaining bolts to the washer
reservoir.
(4) Disconnect the pump and sensor wire connectors.
(5) Disconnect the washer hose.
(6) Disconnect the washer filler hose.
(7) Pivot the inboard side of the reservoir forward
and lift out of vehicle.
(8) Carefully pull the pump out of the reservoir.

NOTE: When replacing the pump, make sure to use
a new grommet for proper sealing and to avoid
leaks.

INSTALLATION
NOTE: When replacing the pump, make sure to use
a new grommet for proper sealing and to avoid
leaks.
(1) Install the new pump grommet.
(2) Position pump motor over grommet and firmly
snap into place.
(3) Place reservoir into position in engine compartment,
pivot the inboard side of the reservoir rearward.
(4) Connect the washer filler hose.
(5) Connect the washer hose.
(6) Connect the pump and sensor wire connectors.
(7) Install the four retaining bolts to the washer
reservoir.
(8) Install the left headlamp assembly. Refer to
Electrical, Lamps/Lighting - Exterior, Headlamp Unit
(Intrepid), Installation.
(9) Connect the negative battery cable remote terminal
to the remote battery post.

click here for J-Intake kit pics and info
Proud seller of J-intakes since 2002
JoeKD is offline  
Sponsored Links
Advertisement
 
post #4 of 9 (permalink) Old 09-24-2003, 01:29 PM Thread Starter
Intrepid Pro
 
Candyman's Avatar
 
Join Date: Aug 2001
Location: Columbus, Ohio
Posts: 1,269
Feedback: 3 / 100%
                     
Thanks Joe, seems like quite a list, I'll take a look at it, try to boost my confidence level on doing it myself! Doesn't look too hard. BTW, what service manual do use?
Candyman is offline  
post #5 of 9 (permalink) Old 09-24-2003, 01:41 PM
Intrepid Pro
 
Join Date: Aug 2001
Location: CT
Posts: 11,278
Feedback: 10 / 100%
                     
that info is from the Mopar LH service manual

there were a couple pics too but trust me, they looked so easy you shouldn't need them
JoeKD is offline  
post #6 of 9 (permalink) Old 09-24-2003, 03:37 PM Thread Starter
Intrepid Pro
 
Candyman's Avatar
 
Join Date: Aug 2001
Location: Columbus, Ohio
Posts: 1,269
Feedback: 3 / 100%
                     
Quote:
Originally posted by JoeKD
that info is from the Mopar LH service manual
I need to get a hold of one of those!
Candyman is offline  
post #7 of 9 (permalink) Old 09-24-2003, 03:38 PM
Intrepid Pro
 
IS300M's Avatar
 
Join Date: Feb 2002
Location: RT 128 + RT 95
Posts: 4,083
Feedback: 0 / 0%
                     
IS300M is offline  
post #8 of 9 (permalink) Old 09-24-2003, 04:20 PM
Intrepid Pro
 
crash459's Avatar
 
Join Date: Sep 2002
Location: Springfield, MA
Posts: 1,139
Feedback: 0 / 0%
                     
I just wrote a "how to" with the service manual link on it.
crash459 is offline  
post #9 of 9 (permalink) Old 09-24-2003, 06:39 PM Thread Starter
Intrepid Pro
 
Candyman's Avatar
 
Join Date: Aug 2001
Location: Columbus, Ohio
Posts: 1,269
Feedback: 3 / 100%
                     
Excellent post Crash, thanks for the download.

It shall come in very handy, I'd print it out if it weren't hundreds of pages long!
Candyman is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the DodgeIntrepid.Net Forums - Dodge Intrepid, Concorde, 300m and Eagle Vision chat forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

Member names may only be composed of alpha-numeric characters. (A-Z and 0-9)

!!ATTENTION ADVERTISERS!! If you intend on advertising anything on this forum, whatsoever, you are required to first contact us here . Additionaly, we do NOT allow BUSINESS NAMES unless you are an Authorized Vendor. If you own a business, and want to do sales on this site via posting or private message, you will need to follow the rules. Shops, Stores, Distributors, Group Buys without being authorized will see your account terminated.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes Rate This Thread
Linear Mode Linear Mode
Rate This Thread:



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome