DodgeIntrepid.Net Forums banner

1 - 14 of 14 Posts

·
Registered
Joined
·
18 Posts
Discussion Starter #1
I bought to 6/9 and i took the one in the back window outand put the new ones in well the old speakers had for wire and the new one only 2 what do i do to get my 6/9 to work i have a 94 intrepid
 

·
Registered
Joined
·
4,811 Posts
When i changed out my 6x9's there were 2 wires into a little black clip (for each speaker). I just cut off the clip and through trial and error found which wires were + and -. It was quite simple in my '94... :rolleyes:
 

·
Registered
Joined
·
533 Posts
I will tell you what I did. Bought a new deck and ran all new wire, but what you can do is 2 of the four wires run the tweeter.If you can get a hold of wiring diagrams they will let you know which. These you can tape with electrical tape and use the other two. Those are from the premium sound that some have. There were actually three levels of stereo speaker setups for the car. Sorry I do not remember which wires are for which. I may be able to look it up on the computer program at work. If anyone has access to alldata, theyy could let youu know.
 

·
Registered
Joined
·
18 Posts
Discussion Starter #4
if any ones got a site post it in here with a wiring diagrams for a 94 intrepid please help me out
 

·
Registered
Joined
·
167 Posts
You could do what i did. Take the wires before the amp(input wires) and run those up to the speakers.
 

·
Registered
Joined
·
4,811 Posts
I forget that some of you guys have the Infinity sound system and the wiring for that is different...
 

·
Registered
Joined
·
533 Posts
Originally posted by gise1:
You could do what i did. Take the wires before the amp(input wires) and run those up to the speakers.
This would work; however, the sound would not be nearly as good if you have the factory deck because it is setup for an amp and if bypassed sounds a little tinny. You could stick an amp in an fix that though.
 

·
Registered
Joined
·
3,018 Posts
u got new 6x9's and u just want to put them in? just cut off the black harness to the factory speakers and wire them to the new speakers,and they wil work. i've done it not a big deal, only a few min.
 

·
Registered
Joined
·
4,811 Posts
Originally posted by Aaron:
u got new 6x9's and u just want to put them in? just cut off the black harness to the factory speakers and wire them to the new speakers,and they wil work. i've done it not a big deal, only a few min.
Thats what i was tryin to say
 

·
Registered
Joined
·
1,461 Posts
Can't do that if you have the Infinity Sound System
 

·
Registered
Joined
·
424 Posts
And its not a matter of just grabbing a wire and attaching it to any other wire, you have to find out which one is positive, also I think if you don't have the infinity sound, (or if someone else put different speakers in) your going to need to remove the back seat and the panels and drop down the rear deck then unscrew the factory ones, and install the new ones from below, thats how I did it, much easier if your speakers blow or you like to change them each time a new model comes out (me :D ) I'll find out the exact color codes for you if you would like...

Spyder
 

·
Registered
Joined
·
366 Posts
hey somebody said something about pputting the rear seats down. yours isnt able to just pull down is it;intrepid rear seats are immovable right? anyways if there is a way to unscrew them and let them move down i wouldnt mind trying that, cus i want to put my amp on the back of the seats but there isnt a lot of room and its harder than hell to get back there and do anything. thanks
 

·
Registered
Joined
·
366 Posts
hey guys also other thatn finding a way to get the rear seats down is buying a hayens or whatever manual worth 15$ i mean does it help a ton? thnaks
 
1 - 14 of 14 Posts
Top